Application guns - customized for your requirements

Build your own 2 component mixing and application gun by using the configurator. Please choose the optimal valve for your demands together with a corresponding gun handle for electric or pneumatic control of the valves. You have various material joints to select, which depends on the characteristics of the material and the used disposable mixers.

Bild nicht verfügbar

2-component valves

2C material valve with 2 cylinder

article number: 0001-9800-0000

Show more information

Pneumatic 2-component valve (aluminium) with retractable pistons, which ensure precise control of spot and shot volume. After each shot, the pistons retract material from the end of the mixing nozzle, to minimise “after drool”. A- and B-component can be separately controlled for example to purge with A-component or to use variable shifting times.

  • Easy to clean / completely dismountable
  • Optional sealings-sets for different chemical formulations and abrasive conditions
  • Optional in stainless steel version, recommended for corrosive acrylics or epoxies
  • Mechanical separation from material-chamber and pneumatic cylinder’s
  • Both pistons lubricated twice with special grease for moisture sensitive adhesives
  • A and B-component can be greased separately to avoid curing in the valve
  • Specially coated pistons to resist abrasive adhesives
  • Optional different material connections, depending on mixing ratio and viscosity
  • Optional night cap’s and ratio check cap
  • Optional retaining nuts and protective pipes for a wide range of static mixers
  • Can be used as hand-held or stationary unit
  • Optional we offer electric or pneumatic handles for actuating the air cylinder at the valve
Connections:
4 x pneumatic hose D=4 mm (outside)
2 x material connection with optional available elbow adapters


2-component valve

article number: 0001-9450-0000

Show more information

Pneumatic 2-component valve (aluminium) with retractable pistons, which ensure precise control of spot and shot volume. After each shot, the dual pistons retract material from the end of the mixing nozzle, to minimise “after drool”.

  • Easy to clean / completely dismountable
  • Optional sealings-sets for different chemical formulations and abrasive conditions
  • Optional in stainless steel version, recommended for corrosive acrylics or epoxies
  • Specially coated pistons to resist abrasive adhesives
  • Optional different material connections, depending on mixing ratio and viscosity
  • Optional night cap’s and ratio check cap
  • Optional retaining nuts and protective pipes for a wide range of static mixers
  • Can be used as hand-held or stationary unit
  • Optional we offer electric or pneumatic handles for actuating the air cylinder at the valve
Connections:
2 x pneumatic hose D=4 mm (outside)
2 x material connection with optional available elbow adapters


Pistol grips

Pistol grip pneumatic

article number: 0001-9500-0000P

Show more information

Pistol grip for 2 component valve

  • Grab handle / handhold with trigger pneumatically controlled
  • Incl. manually operated pneumatic valve
  • 5/2 way valve (installed in the handle)
  • Inlet pressure max. 0-10 bar
  • Nominal flow 125 l/m
  • Switching power 6 bar (14 N)
  • 3 x pneumatic hose D=4 mm (outside)
  • Low weight
  • Ergonomically designed
  • Dismountable


Pistol grip electric

article number: 0001-9500-0000E

Show more information

Pistol grip for 2 component valve

  • Grab handle / handhold with trigger
  • Electrically controlled
  • Make contact / key button for 24 V on the trigger
  • 5 m connecting cable (2x0,5mm²)
  • Low weight
  • Ergonomically designed
  • Dismountable 


Sealing material joints

Sealing material joint 1:1

article number: 0001-9400-0200

Show more information

The material joint passes the A- and B-component separately into the mixer. For cleaning just remove the mixer and clean the surface of the outlet.

Consisting of:

  • 1 x material joint (aluminium) for mixing ratio 1 : 1
  • 2 x O-ring
  • 4 x screw for mounting at the material valve
Optional:
suitable night cap 0001-9998-0009-1/1


Sealing material joint 1:1 highflow

article number: 0001-9400-0201

Show more information

The material joint passes the A- and B-component separately into the mixer. For cleaning just remove the mixer and clean the surface of the outlet.

Consisting of:

  • 1 x material joint (aluminium) for mixing ratio 1 : 1 with high outlet rate
  • 2 x O-ring
  • 4 x screw for mounting at the material valve
Optional:
suitable night cap 0001-9998-0009-1/1


Sealing material joint 10:1

article number: 0001-9400-0202

Show more information

The material joint passes the A- and B-component separately into the mixer. For cleaning just remove the mixer and clean the surface of the outlet.

Consisting of:

  • 1 x material joint (aluminium) for mixing ratio 10 : 1
  • 2 x O-ring
  • 4 x screw for mounting at the material valve
Optional:
suitable night cap 0001-9998-0009-10/1


Sealing material joint SI

article number: 0001-9400-0203

Show more information

The material joint passes the A- and B-component separately into the mixer. For cleaning just remove the mixer and clean the surface of the outlet.

Consisting of:

  • 1 x material joint (aluminium) with centre-fed for B-component; recommended for silicone
  • 2 x O-ring
  • 4 x screw for mounting at the material valve
Optional:
suitable night cap 0001-9998-0022


Sealing material joint SI long B-component

article number: 0001-9400-0207

Show more information

The material joint passes the A- and B-component separately into the mixer. For cleaning just remove the mixer and clean the surface of the outlet.

Consisting of:

  • 1 x material joint (steel / galvanized) with long centre-fed for B-component; recommended for silicone
  • 2 x O-ring
  • 4 x screw for mounting at the material valve


Cap nut for one way mixer

Cap nut for one way mixer with outside diameter 7.62 mm to 9.40 mm

article number: 0001-9998-0010B

Show more information

With this nut you can fix the one way mixers to the material joints. After you finished working, just remove the mixer, clean the surface of the outlet and cover the sealing joint with a night cap.

  • For mixer product code 0001-9998-04... until 0001-9998-06...
  • For mixer with outside diameter 7.62 mm to 9.40 mm
  • Nut made of aluminium
  • Fit also to our night caps


    Cap nut for one way mixer with outside diameter 11.71 mm to 17.00 mm

    article number: 0001-9998-0010

    Show more information

    With this nut you can fix the one way mixers to the material joints. After you finished working, just remove the mixer, clean the surface of the outlet and cover the sealing joint with a night cap.

    • For mixer product code 0001-9998-07... until 0001-9998-13...
    • For mixer with outside diameter 11.71 mm to 17.00 mm
    • Nut made of aluminium
    • Fit also to our ratio checking nozzles