Two-component mixing and metering gear pump system for robot connection. The mastermix gear drive robot is a gear pump metering system, especially designed to process fast curing 2-component materials with robots or linear systems. The systems high accuracy of dosing allows the usage of disposable plastic mixers. Thereby the loss of material due to base purging, as well as the costs for consumables and spare parts, are reduced to a minimum. Short amortisation of investment is the result of the high costsaving potential of this system. For certain materials, an eccentric screw pump can be used as an alternative to the gear pump. Technical data: outflow depending on viscosity, temperature, batch of material etc. A-side powered pneumatic B-side powered pneumatic power supply 3 x 400 V+N+PE/ 3.8 kW compressed air requirement 6 bar, 600 l/min. dimensions l x w x h 1500 x 1000 x 1800 mm weight approx. 620 kg Standard equipment*: Siemens S7-1500 / touch panel / ethernet-ready for integration in automation Software interface is prepared to control automation (standard via Profinet; other interfaces on request) Siemens servomotors digital pressure sensors dead volume-free construction optical and acoustic pot life control signal light (visual alert for system messages) material shortage control overpressure safety device residual materials optimized following plate two hand safety control for A- and B-side drum shortage control with pump stop maintenance free pump sealing system manual dosage control variably adjustable mixing ratio 200 l A drum / 20 l B drum optimized change of 200 litre drum (base plate with recesses for jack lift) *depending on the project, positions may differ Aditional equipment: other drum sizes on request following plate heating A-component and B-component cartridge filling unit (1c and 2c) park position with automatic purging permanent mixing ratio control with volume measuring cells working-hose prolongation special painting on request Further options please find in our brochure "Optional for mastermix series" or on request.  

Two-component mixing and metering gear pump system. The mastermix gear drive is a servo-motor controlled gear pump metering system which enables the reliable processing of even the most sensible materials. The systems extreme high accuracy of dosing allows the usage of disposable plastic mixers. Thereby the loss of material due to base purging, as well as the costs for consumables and spare parts, are reduced to a minimum.The very quick amortisation of the investment is the result of the high cost-saving potential of the system. For certain materials, an eccentric screw pump can be used as an alternative to the gear pump. Technical data: outflow depending on viscosity, temperature, batch of material etc. A-side powered pneumatic B-side powered pneumatic power supply 3 x 400 V+N+PE/ 3.8 kW compressed air requirement 6 bar, 600 l/min. dimensions l x w x h 1500 x 1000 x 1800 mm height with swivel arm 2500 mm standard swivel arm length 1200 mm standard hose length 2500 mm weight approx. 640 kg Standard equipment*: Siemens S7-1500 / touch panel / ethernet-ready for integration in future automation Software interface is prepared to control automation (standard via Profinet; other interfaces on request) Siemens servomotors digital pressure sensors dead volume-free construction optical and acoustic pot life control signal light (visual alert for system messages) material shortage control overpressure safety device residual materials optimized following plate two hand safety control for A- and B-side drum shortage control with pump stop maintenance free pump sealing system variably adjustable mixing ratio optimized change of 200 litre drum (base plate with recesses for jack lift) *depending on the project, positions may differ Additional equipment: other drum sizes on request following plate heating A-component and B-component cartridge filling unit (1c and 2c) park position with automatic purging permanent mixing ratio control with volume measuring cells working-hose prolongation special painting on request swivel arm prolongation swivel arm heightening mobile unit, with wheels Further options please find in our brochure "Optional for mastermix series" or on request.

Two-component mixing and metering gear pump system. The mastermix gear drive compact is a gear pump metering system especially designed for the processing of fast curing 2-component products. The highly compact system, designed for mobile application equals in performance to a standard system. The system high accuracy of dosing allows the usage of disposable plastic mixers. Thereby the loss of material due to base purging, as well as the costs for consumables and spare parts, are reduced to a minimum. The very quick amortisation of the investment is the result of the high cost-saving potential of the system. For certain materials, an eccentric screw pump can be used as an alternative to the gear pump. Technical data: outflow depending on viscosity, temperature, batch of material etc. A-side powered pneumatic B-side powered pneumatic power supply 3 x 400 V + N + PE / 3,8 kW compressed air requirement 6 bar; 600 l/min. dimensions l x w x h 1200 x 800 x 2200 mm standard hose length 2500 mm weight approx. 640 kg Standard equipment*: Siemens S7-1500 / touch panel / ethernet-ready for integration in future automation Software interface is prepared to control automation (standard via Profinet; other interfaces on request) Siemens servomotors digital pressure sensors dead volume-free construction optical and acoustic pot life control signal light (visual alert for system messages) material shortage control overpressure safety device residual materials optimized following plate two hand safety control for A- and B-side drum shortage control with pump stop maintenance free pump sealing system variably adjustable mixing ratio 20 l A-drum / 20 l B-drum *depending on the project, positions may differ Aditional equipment: other drum sizes on request following plate heating A-component and B-component cartridge filling unit (1c and 2c) park position with automatic purging permanent mixing ratio control with volume measuring cells working-hose prolongation special painting on request swivel arm systems mobile unit, with wheels Further options please find in our brochure "Optional for mastermix series" or on request.

2 component mixing and metering unit with gear pump techology. The mastermix LV drive is a servo-motor controlled two-component mixing and metering system to process low to medium viscose materials. The systems extreme high accuracy of dosing allows the usage of disposable plastic mixers. Thereby the loss of material due to base purging, as well as the costs for consumables and spare parts, are reduced to a minimum. For certain materials, an eccentric screw pump can be used as an alternative to the gear pump. Technical data: outflow max. depending on material* power supply 3 x 400 V + N + PE/ 3.8 kW compressed air requirement 6 bar, oil-free, dried, filtered dimensions (l x w x h) depending on application weight approx. depending on application *depending on viscosity, temperature, batch of material etc. Standard equipment*: Siemens S7-1500 / touch panel / ethernet-ready for integration in automation Software interface is prepared to control automation (standard via Profinet; other interfaces on request) dead volume-free construction Siemens servomotors two gear pumps digital pressure sensors overpressure safety device material shortage control pot life control with visual and audible warning signal drum shortage control with pump stop maintenance free pump sealing system variably adjustable mixing ratio *depending on the application, equipment may differ Additional equipment: material supply system* permanent mixing ratio control by volume measuring cells additional manual dosage control frames and collecting tanks for drums or IBC-container storage tanks in special sizes (depending on application) different versions of application units and valves available * the design of the material supply is adapted to the intended use and to each client individually more options on request

Two-component mixing and metering gear pump system. The mastermix gear basic is a gear pump metering system especially designed for the processing of two component silicones. As a basic version of our mastermix gear series it is uncompromisingly  geared to functionality and offers gear pump metering for a favorable price. The systems precise accuracy of dosing allows the usage of disposable plastic mixers. Thereby the loss of material due to base purging, as well as the costs for consumables and spare parts, are reduced to a minimum.Technical data: outflow depending on viscosity, temperature, batch of material etc. A-side powered pneumatic B-side powered pneumatic power supply 3 x 400 V + N + PE/ 3.8 kW compressed air requirement 6 bar, 600 l/min. dimensions l x w x h 1500 x 1000 x 1800 mm height with swivel arm 2500 mm standard swivel arm length 1200 mm standard hose length 2500 mm weight approx. 620 kgStandard equipment*: Siemens S7-1200 / ethernet-ready for integration in future automation optical and acoustic pot life control material shortage control overpressure safety device residual materials optimized following plate two hand safety control drum shortage control with pump stop maintenance free pump sealing system manual dosage control variably adjustable mixing ratio 200 l A drum / 20 l B drum optimized change of 200 litre drum (base plate with recesses for jack lift) *depending on the project, positions may differAdditional equipment: swivel arm prolongation swivel arm heightening working-hose prolongation special painting B component pump for 200 l drum other drum sizes on request following plate heating A-component and B-component cartridge filling unit (1c and 2c) mobile unit, with wheels park position with automatic purging more options on request

Two-component mixing and metering gear pump system. The mastermix gear basic compact is a gear pump metering system, especially designed for the processing of two component silicones. As a compact and space-saving version of our mastermix gear series it is uncompromisingly geared to functionality and offers gear pump metering for a favorable price. The systems precise accuracy of dosing allows the usage of disposable plastic mixers. Thereby the loss of material due to base purging, as well as the costs for consumables and spare parts, are reduced to a minimum. Technical data: outflow depending on viscosity, temperature, batch of material etc. A-side powered pneumatic B-side powered pneumatic power supply 3 x 400 V + N + PE/ 3.8 kW compressed air requirement 6 bar, 600 l/min. dimensions l x w x h 900 x 600 x 1500 mm standard hose length 2500 mm weight approx. 380 kg Standard equipment*: Siemens S7-1200 / ethernet-ready for integration in future automation optical and acoustic pot life control material shortage control overpressure safety device two hand safety control drum shortage control with pump stop maintenance free pump sealing system manual dosage control variably adjustable mixing ratio 20 l A drum / 20 l B drum *depending on the project, positions may differ Additional equipment: swivel arm systems working-hose prolongation special painting A- and B-component pump for 20 l drum, other sizes on request heated following plate for A- and/or B-component more options on request

2 component mixing and metering unit with gear pump technology. The mastermix LV is a two-component mixing and metering system to process low to medium viscose materials. Our special strength is to focus on our clients requirements, to design individual solutions from our large base of standard equipment. We are looking forward for your specifications. Technical data: outflow max. depending on material * power supply 3 x 400 V + N + PE/50 Hz/16 A compressed air requirement 6 bar, oil-free, dried, filtered dimensions (l x w x h)* depending on application weight approx.** depending on application *depending on viscosity, temperature, batch of material etc. Standard equipment*: Siemens S7-1200 / touch panel / ethernet-ready for integration in future automation 2 x SEW gearmotor, frequency-controlled 2 x gear pump digital pressure sensors overpressure safety device material shortage control pot life control with visual and audible warning signal signal lamp to provide a visual alert for system messages 2 x storage tank approx. 26 litre digital fill level control of storage tank 2c material valve *depending on the application, positions may differ Additional equipment: material supply system* heated material hoses mobile underframe hose elongations flow rate control frames and collecting tanks for drums or IBC-container storage tanks in special sizes (project-specific) different versions of application units and valves * the design of the material supply is adapted to the intended use and to each individual client. more options on request