Technical information: Suitable for all material valves 0001-9450-…. Suitable for all material valves 0001-9800-…. Suitable for all material valves 0001-9300-….

Technical information: Suitable for all sealing material joints 0001-9400-…. Suitable for all material valves 0001-9450-…. Suitable for all material valves 0001-9800-…. Extra wear-resistant (V-Variants)

For material valves version: 0001-9800-0000 and 0001-9450-0000

For 2C material valve version 0001-9800-0000.

suitable for grease gun 0001-9998-0031GUN for lubricating - material valve 0001-9800-0000 for sealing night caps and material connections

The material joint passes the A- and B-component separately into the mixer. For cleaning just remove the mixer and clean the surface of the outlet. Consisting of: 1 x material joint (aluminium) for mixing ratio 10 : 1 specially for liquid B component 2 x O-ring 4 x screw for mounting at the material valve

With this night cap you can close the material joints during work breaks. For material joints version: 0001-9400-0200 and 0001-9400-0200VA 0001-9400-0201 and 0001-9400-0201VA

The material joint passes the A- and B-component separately into the mixer. For cleaning just remove the mixer and clean the surface of the outlet. Consisting of: 1 x material joint (aluminium) for mixing ratio 1 : 1 2 x O-ring 4 x screw for mounting at the material valve

Nozzle to check the mixing ratio (white version made of PTFE). For material joints version: 0001-9400-0202 0001-9400-0202VA

The protective pipe is used to attach static mixers to the t-s-i.de material joints. It ensures a clean connection and thus prevents material from leaking between the material joint and the mixer. It also serves as a guide for the mixer in order to compensate for its elastic behavior and any shape deviations, which can be particularly problematic with long mixers. Attention: Only tighten hand-tight and without tools! Thin-walled construction for low weight and easy handling Available in different versions for different mixers Compatible with t-s-i.de material joints

The protective pipe is used to attach static mixers to the t-s-i.de material joints. It ensures a clean connection and thus prevents material from leaking between the material joint and the mixer. It also serves as a guide for the mixer in order to compensate for its elastic behavior and any shape deviations, which can be particularly problematic with long mixers. Attention: Only tighten hand-tight and without tools! Thin-walled construction for low weight and easy handling Available in different versions for different mixers Compatible with t-s-i.de material joints

With this night cap you can close the material joints during work breaks. For material joints version: 0001-9400-0203 0001-9400-0203VA

With this night cap you can close the material joints during work breaks. For material joints version: 0001-9400-0202 0001-9400-0202VA

For 2-component valve 0001-9450-0000.

The material joint passes the A- and B-component separately into the mixer. For cleaning just remove the mixer and clean the surface of the outlet. Consisting of: 1 x material joint (stainless steel) with centre-fed for B-component; recommended for silicone 2 x O-ring 4 x screw for mounting at the material valve

The protective pipe is used to attach static mixers 0001-9998-1236 to the t-s-i.de material joints. It ensures a clean connection and thus prevents material from leaking between the material joint and the mixer. It also serves as a guide for the mixer in order to compensate for its elastic behavior and any shape deviations, which can be particularly problematic with long mixers. Additionally, there is an outer thread at the tip of 0001-9998-0200 to connect the following adapters: 2000-0306-1004T (Adapter rubber nozzle) 2000-0306-1005T (Adapter male thread M15x1,5) 2000-0306-1011T (Adapter male cartridge coarse thread S15) 2000-0306-1012T (Adapter female thread 1/4" NPT) Attention: Only tighten hand-tight and without tools! For use with mixer 0001-9998-1236 Additional outer thread to use nozzles with t-s-i.de adapters Thin-walled construction for low weight and easy handling Available in different versions for different mixers Compatible with t-s-i.de material joints

The material joint passes the A- and B-component separately into the mixer. For cleaning just remove the mixer and clean the surface of the outlet. Consisting of: 1 x material joint (aluminium) for mixing ratio 10 : 1 2 x O-ring 4 x screw for mounting at the material valve

Pneumatic 2-component valve (aluminium) with retractable piston, which ensures precise control of spot and shot volume. After each shot, the dual pistons retract material from the end of the mixing nozzle, to minimise “after drool”. Easy to clean / completely dismountable Optional in stainless steel version, recommended for corrosive acrylics or epoxies Specially coated pistons to resist abrasive adhesives Optional different material connections, depending on mixing ratio and viscosity Optional night cap’s and ratio check cap Optional retaining nuts and protective pipes for a wide range of static mixers Can be used as hand-held or stationary unit Optional we offer electric or pneumatic handles for actuating the air cylinder at the valve Max. material pressure 360 bar (dependent upon system) Connections: 2 x pneumatic hose D=4 mm (outside) / M5 Thread 2 x material connection with optional available elbow adaptersM14 x 1.5 Mounting thread for handle M4

Nozzle to check the mixing ratio (white version made of PTFE) incl. cap nut. For material joints version: 0001-9400-0200 0001-9400-0200VA 0001-9400-0201 0001-9400-0201VA

With this nut you can fix the one way mixers to the material joints. After you finished working, just remove the mixer, clean the surface of the outlet and cover the sealing joint with a night cap. For mixers with bell 19.9mm Nut made of aluminium Fit also to our night caps

The Teflon-coated adapter enables the installation of all nozzles with a M15x1.5 thread and thus a wide range of possible uses. IMPORTANT: The scope of delivery only includes the adapter without protective tube or nozzle! Technical characteristics: Teflon coating for easy and fast cleaning Internal thread on the inlet side for easy mounting on the t-s-i.de protective pipes with external thread (e.g. 0001-9998-0200) Including O-Ring to properly seal on the static mixer M15x1.5 thread on the outlet side for mounting numerous nozzles

Pneumatic 2-component valve (aluminium) with retractable pistons, which ensure precise control of spot and shot volume. After each shot, the pistons retract material from the end of the mixing nozzle, to minimise “after drool”. A- and B-component can be separately controlled for example to purge with A-component or to use variable shifting times. Easy to clean / completely dismountable Optional in stainless steel version, recommended for corrosive acrylics or epoxies Mechanical separation from material-chamber and pneumatic cylinder’s Both pistons lubricated twice with special grease for moisture sensitive adhesives A and B-component can be greased separately to avoid curing in the valve Specially coated pistons to resist abrasive adhesives Optional different material connections, depending on mixing ratio and viscosity Optional night cap’s and ratio check cap Optional retaining nuts and protective pipes for a wide range of static mixers Can be used as hand-held or stationary unit Optional we offer electric or pneumatic handles for actuating the air cylinder at the valve Max. material pressure 360 bar (dependent upon system) Connections: 4 x pneumatic hose D=4 mm (outside) / M5 Thread 2 x material connection with optional available elbow adaptersM14 x 1.5 Mounting thread for handle M4

With this nut you can fix the one way mixers to the material joints. After you finished working, just remove the mixer, clean the surface of the outlet and cover the sealing joint with a night cap. For mixer product code 0001-9998-04... until 0001-9998-06... For mixer with outside diameter 7.62 mm to 9.40 mm Nut made of aluminium Fit also to our night caps  

Flow direction from 8S to 1/4" Wrench size of the union nut 19(Wrench size of the valve 19)